| 属性 | 典型值 | UNITS | 测试手段 |
|---|
| MECHANICAL |
|---|
| Flexural Stress, yld, 1.3 mm/min, 50 mm span | 86 | MPa | ASTM D790 |
| Flexural Modulus, 1.3 mm/min, 50 mm span | 2300 | MPa | ASTM D790 |
| Tensile Stress, yield, 50 mm/min | 54 | MPa | ISO 527 |
| Tensile Stress, break, 50 mm/min | 56 | MPa | ISO 527 |
| Tensile Strain, yield, 50 mm/min | 4.5 | % | ISO 527 |
| Tensile Strain, break, 50 mm/min | 100 | % | ISO 527 |
| Tensile Modulus, 1 mm/min | 2200 | MPa | ISO 527 |
| Flexural Stress, yield, 2 mm/min | 82 | MPa | ISO 178 |
| Flexural Modulus, 2 mm/min | 2200 | MPa | ISO 178 |
| IMPACT |
|---|
| Instrumented Dart Impact Total Energy, 23°C | 55 | J | ASTM D3763 |
| Instrumented Dart Impact Total Energy, -30°C | 65 | J | ASTM D3763 |
| Izod Impact, unnotched 80*10*3 +23°C | PASSES | kJ/m² | ISO 180/1U |
| Izod Impact, notched 80*10*4 +23°C | 55 | kJ/m² | ISO 180/1A |
| Izod Impact, notched 80*10*4 -30°C | 40 | kJ/m² | ISO 180/1A |
| Charpy 23°C, Unnotch Edgew 80*10*3 sp=62mm | NB | kJ/m² | ISO 179/1eU |
| Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm | 60 | kJ/m² | ISO 179/1eA |
| Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm | 45 | kJ/m² | ISO 179/1eA |
| THERMAL |
|---|
| Vicat Softening Temp, Rate B/50 | 129 | °C | ASTM D1525 |
| HDT, 0.45 MPa, 3.2 mm, unannealed | 128 | °C | ASTM D648 |
| HDT, 1.82 MPa, 3.2mm, unannealed | 108 | °C | ASTM D648 |
| CTE, -40°C to 40°C, flow | 7.E-05 | 1/°C | ASTM E831 |
| CTE, -40°C to 40°C, xflow | 7.E-05 | 1/°C | ASTM E831 |
| Ball Pressure Test, 75°C +/- 2°C | PASSES | - | IEC 60695-10-2 |
| Ball Pressure Test, approximate maximum | 100 | °C | IEC 60695-10-2 |
| Vicat Softening Temp, Rate B/120 | 130 | °C | ISO 306 |
| HDT/Bf, 0.45 MPa Flatw 80*10*4 sp=64mm | 126 | °C | ISO 75/Bf |
| HDT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm | 106 | °C | ISO 75/Af |
| PHYSICAL |
|---|
| Specific Gravity | 1.14 | - | ASTM D792 |
| Mold Shrinkage, flow, 3.2 mm | 0.5-0.7 | % | SABIC method |
| Mold Shrinkage, xflow, 3.2 mm | 0.5-0.7 | % | SABIC method |
| Density | 1.14 | g/cm³ | ISO 1183 |
| Water Absorption, (23°C/24hrs) | 0.3 | % | ISO 62-1 |
| Water Absorption, (23°C/saturated) | 0.4 | % | ISO 62-1 |
| Moisture Absorption (23°C / 50% RH) | 0.13 | % | ISO 62 |
| Melt Volume Rate, MVR at 260°C/5.0 kg | 20 | cm³/10 min | ISO 1133 |
| Melt Volume Rate, MVR at 265°C/5.0 kg | 25 | cm³/10 min | ISO 1133 |
| ELECTRICAL |
|---|
| Volume Resistivity | >1.E+16 | Ω.cm | IEC 60093 |
| Surface Resistivity, ROA | >1.E+16 | Ω | IEC 60093 |
| Dielectric Strength, in oil, 0.8 mm | 39 | kV/mm | IEC 60243-1 |
| Dielectric Strength, in oil, 1.6 mm | 25 | kV/mm | IEC 60243-1 |
| Dielectric Strength, in oil, 3.2 mm | 17 | kV/mm | IEC 60243-1 |
| Injection Molding |
|---|
| Drying Temperature | 95 - 105 | °C | |
| Drying Time | 2 - 4 | Hrs | |
| Maximum Moisture Content | 0.02 | % | |
| Melt Temperature | 260 - 290 | °C | |
| Nozzle Temperature | 240 - 280 | °C | |
| Front - Zone 3 Temperature | 250 - 290 | °C | |
| Middle - Zone 2 Temperature | 250 - 290 | °C | |
| Rear - Zone 1 Temperature | 230 - 260 | °C | |
| Hopper Temperature | 60 - 80 | °C | |
| Mold Temperature | 60 - 90 | °C | |
